At Nationwide Boiler we continuously upgrade our stock of rental equipment, allowing us to offer our customers a variety of options to fit each individual need. We are currently assembling two (2) 650 HP, 250 psig design, low NOx mobile boiler rooms. Below are some pictures of one of the boilers being put into its trailer, take a look!
Routine boiler maintenance is imperative not only for safety, but also to sustain efficiency and reliability of your system. Being proactive rather than reactive is likely to increase the longevity of your boiler as well as help prevent incidents that can result in injuries, damage, or worse. Incorporating routine maintenance into your facilities day-to-day operations will prove its worth with a great deal of short- and long-term benefits.
There are certain maintenance tasks that should be performed daily, and others that should be performed periodically. Below we have provided a list of best practices to follow when putting together your routine boiler maintenance plan.
On a daily basis, you should track and keep a log of the following items:
Blowdown of the boiler (bottom blow) and water column should also be performed on a daily basis. In addition, you should observe boiler and auxiliary equipment daily to ensure proper operation and that there is no damage, leaks, or unusual behavior.
On a weekly to monthly basis, it’s important to conduct additional visual inspections and observe the operation of certain components for areas that may need to be addressed. This includes:
When it comes to the burner, you should inspect the valves, pilot tube, and diffuser thoroughly for any signs of wear that might call for a repair. Also, be sure to observe the entirety of the boiler system for potential hot spots (an indicator of deteriorated refractory) and again, be sure to keep an eye out for any leaks of fuel, water, or flue gas.
Lastly, there are certain items that should be performed on a semi-annual to annual basis. Many of the tasks below can be checked off during the annual inspection, when the boiler is taken offline:
This is also a good time to fully inspect the auxiliaries that provide fuel, air, water, and chemicals to the boiler. In addition, combustion should be reset periodically with the use of a combustion analyzer, for accurate readings of NOx, CO, and O2.
While the guidelines above provide a good baseline of tasks to perform when it comes to routine maintenance, be sure to consider the boiler manufacturer’s recommendations as well.
Combustion equipment safety is essential for the daily operation of facilities and safety of plant personnel. Safety protocols and mechanisms in industrial plants have improved drastically in the last century, but incidents still occur far too frequently. Because boiler systems are inherently dangerous, safety must be factored into the design of not just the boiler, but also the burner, combustion control, and the overall operation of the system.
The burner management system (BMS) is just one of many safety devices built into a boiler system, designed to control the combustion process from beginning to end in a safe and reliable manner. It monitors high and low gas pressure, the combustion air fan, combustion air, and water levels, in addition to monitoring safety devices and controlling the sequence of lighting the burner. If any issues arise related to pressure or water level, it will initiate closure of the shut-off valves. To automate these processes, PLC-based controls are often used as a BMS. PLC based BMS gives you much more flexibility, the ability to use analog input signals as limits, limit voting and the versatility to have almost unlimited safety limits.
A Programmable Logic Controller (PLC) is a robust computer utilized for industrial automation. Although a PLC doesn’t physically look like a typical computer, it incorporates the very same technology seen in computers and smart devices that we use every day. The PLC receives information from connected sensors or input devices, processes the data, and triggers outputs based on pre-programmed parameters. It consists of a power supply, a CPU (central processing unit), input and output cards, and communication cards. A programming device (often a laptop computer) is utilized for writing programs into the PLC and HMI (human machine interface) which provides a visual model of the system as a whole.
Compared to traditional technologies, a PLC-based system is easier to troubleshoot, more reliable, more cost-effective, and much more versatile. In addition, PLC-based controls provide added levels of safety for the burner management system and overall operation of your boiler. PLCs are built in compliance with NFPA 85 and SIL2 requirements at minimum and can be configured to meet SIL3 standards as well. Therefore, we are seeing boiler control panels being built or updated to PLC-based systems more than ever.
Pacific Combustion Engineering has extensive knowledge and experience in the design, build, and programming of PLC-based combustion control systems. If you are in the market for an upgrade or brand-new panel that incorporates PLC, give us a call and we will design a system that fits your unique process needs.
